• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar

Yellow Bricks

by Duncan Epping

  • Home
  • Unexplored Territory Podcast
  • HA Deepdive
  • ESXTOP
  • Stickers/Shirts
  • Privacy Policy
  • About
  • Show Search
Hide Search

4.0

ESXi disk size requirement?

Duncan Epping · Oct 27, 2010 ·

I’ve seen this question passing by a couple of times now and I found myself going through the document to dig up the reference. I thought it would come in handy to document it:

Q) What is the disk size requirements for ESXi installable?
A) The minimal required disk size is 5GB (Page 24, ESXi Installable and vCenter Server Setup Guide), recommend is 6GB (KB: http://kb.vmware.com/kb/1026500)

Service Console Memory, a common misunderstanding (ESX 4.0+)

Duncan Epping · Sep 21, 2010 ·

I was reading the Maximum vSphere book by Eric Siebert today and noticed something that I also spotted in Scott Lowe’s Mastering VMware Sphere book. Both Scott and Eric described the fact that the default amount of assigned Service Console memory for ESX has been increased from 272MB to X. I deliberately use “X” as both Eric and Scott mention a different value in their book.

The reason both Scott and Eric mention a different value in their book can be easily explained though, and I wrote about this a while ago, as of vSphere 4.0 there is no default value anymore. I gave this feedback to Scott a while back and of course he asked where this was documented. Back then it was nowhere to be found, well except for on my blog but that is not an official VMware publication. I asked our KB team to update the KB article that explains Service Console memory and I just noticed that they have:

src

ESX 4.x hosts – the default amount of RAM is dynamically configured to a value between 300MB and 800MB, depending on the amount of RAM that is installed in the host. For example, if the host has 32GB of memory the service console RAM will be set to 500MB, while a host which has 128GB of RAM will see the service console RAM set to 700MB. The maximum has not changed from 800MB, which would be seen on hosts with 256GB of RAM or higher, if it is being dynamically allocated.

This is exactly what I observed almost a year ago:

  • ESX Host – 8GB RAM -> Default allocated Service Console RAM = 300MB
  • ESX Host – 16GB RAM -> Default allocated Service Console RAM = 400MB
  • ESX Host – 32GB RAM -> Default allocated Service Console RAM = 500MB
  • ESX Host – 64GB RAM -> Default allocated Service Console RAM = 602MB
  • ESX Host – 96GB RAM -> Default allocated Service Console RAM = 661MB
  • ESX Host – 128GB RAM -> Default allocated Service Console RAM = 703MB
  • ESX Host – 256GB RAM -> Default allocated Service Console RAM = 800MB

Just wanted to point this out as I am certain that many people will not be aware of this.

Two new HA Advanced Settings

Duncan Epping · Aug 23, 2010 ·

Just noticed a couple of new advanced settings in the vCenter Performance Best Practices whitepaper.
  • das.perHostConcurrentFailoversLimit
    When multiple VMs are restarted on one host, up to 32 VMs will be powered on concurrently by default. This is to avoid resource contention on the host. This limit can be changed through the HA advanced option: das.perHostConcurrentFailoversLimit. Setting a larger value will allow more VMs to be restarted concurrently and might reduce the overall VM recovery time, but the average latency to recover individual VMs might increase. We recommend using the default value.
  • das.sensorPollingFreq
    The das.sensorPollingFreq option controls the HA polling interval. HA polls the system periodically to update the cluster state with such information as how many VMs are powered on, and so on. The polling interval was 1 second in vSphere 4.0. A smaller value leads to faster VM power on, and a larger value leads to better scalability if a lot of concurrent power operations need to be performed in a large cluster. The default is 10 seconds in vSphere 4.1, and it can be set to a value between 1 and 30 seconds.

I want to note that I would not recommend changing these. There is a very good reason the defaults have been selected. Changing these can lead to instability, however when troubleshooting they might come in handy.

vCenter Resiliency?

Duncan Epping · Aug 12, 2010 ·

After the whole MSCS’ed vCenter support discussion VMware Technical Marketing reached out to me. Lets be clear, the intention of this article is not to change support. The intention of this article is to get an idea of how many of you would be interested in seeing a whitepaper on vCenter resiliency with MSCS/VCS which could be supported on best effort by GSS.

I was asked to figure out what would most interest you. I appreciate any comments around this but specifically would love to have answers on the following:

  • Based on which technology would you prefer to see a whitepaper? MSCS or Veritas Clustering?
  • Would you be looking for a total solution including VMware Update Manager and Orchestrator or just purely vCenter Server? In case of the total package, why?
  • Are there any other components that would need to be included in a whitepaper?

Again, any help / answer / comment is very much appreciated.

High physical switch CPU load?

Duncan Epping · Aug 4, 2010 ·

One of my customers experienced high CPU load on their physical switch. After some investigation they noticed broadcasts packets being sent every two seconds. The first reaction was Beacon Probing is probably enabled.

Unfortunately this wasn’t the case. But VMware GSS came to the rescue and pointed us towards a KB article. Apparently a bug has been identified in 4.0 which causes this behaviour:

src: http://kb.vmware.com/kb/1024435

Problem:

  • ESX sends Beacon Packets when vDS/vSwitch are connected to more than one uplink.
  • ESX server sends periodic broadcast of Beacon Packets even if the vSwitch/vNetwork Distributed Switch (vDS) is not configured to use Beacon Probing for Network Failover Detection.
  • These packets have the virtual MAC of the vmnic in the Source MAC Address field.

Workaround:

#esxcfg-advcfg -s 0 /Net/MaxBeaconsAtOnce

The customer implemented this workaround and the problem is gone… From what I have been told this issue does not exist in ESX(i) 4.1 so if you are experiencing it, an upgrade might be a better solution. In this case due to the size of the environment that was not an option.

  • « Go to Previous Page
  • Page 1
  • Page 2

Primary Sidebar

About the Author

Duncan Epping is a Chief Technologist and Distinguished Engineering Architect at Broadcom. Besides writing on Yellow-Bricks, Duncan is the co-author of the vSAN Deep Dive and the vSphere Clustering Deep Dive book series. Duncan is also the host of the Unexplored Territory Podcast.

Follow Us

  • X
  • Spotify
  • RSS Feed
  • LinkedIn

Recommended Book(s)

Also visit!

For the Dutch-speaking audience, make sure to visit RunNerd.nl to follow my running adventure, read shoe/gear/race reviews, and more!

Do you like Hardcore-Punk music? Follow my Spotify Playlist!

Do you like 80s music? I got you covered!

Copyright Yellow-Bricks.com © 2026 · Log in